Extended General-Purpose Holding User Variables
Standart Software
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8000~8001 |
General-purpose holding user variable (extended) 0 |
-2147483648 |
2147483647 |
|
|
|
8002~8003 |
General-purpose holding user variable (extended) 1 |
-2147483648 |
2147483647 |
|
|
|
8004~8005 |
General-purpose holding user variable (extended) 2 |
-2147483648 |
2147483647 |
|
|
|
… |
… |
-2147483648 |
2147483647 |
|
|
|
… |
… |
-2147483648 |
2147483647 |
|
|
|
… |
… |
-2147483648 |
2147483647 |
|
|
|
9994~9995 |
General-purpose holding user variable (extended) 997 |
-2147483648 |
2147483647 |
|
|
|
9996~9997 |
General-purpose holding user variable (extended) 998 |
-2147483648 |
2147483647 |
|
|
|
9998~9999 |
General-purpose holding user variable (extended) 999 |
-2147483648 |
2147483647 |
|
|
|
|
There are a total of 1000 extended general-purpose holding user variables. They are sequentially assigned starting from address 8000. They can store 32-bit data. These variables can be used for purposes such as storing user macros or program package data. When the power is turned off and then on again, the contents of these variables remain unchanged |
Drilling Unit Active
When drilling group offsets are activated with PRM336, variables from 4500 to 4649 are used as 50 tool offsets. To make these offsets valid, the G43/G44 H command must also be issued. The first tool of the drilling group starts from tool 51. For the first tool, G43/G44 H51 should be given.
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
9000~9001 |
Drilling group 1st tool X offset |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
9002~9003 |
Drilling group 1st tool Y offset |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
9004~9005 |
Drilling group 1st tool Z offset |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
… |
… |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
… |
… |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
… |
… |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
9294~9295 |
Drilling group 50th tool X offset |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
9296~9297 |
Drilling group 50th tool Y offset |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
9298~9299 |
Drilling group 50th tool Z offset |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
Laser Cutting Software
The list of parameters used in the laser cutting machine is as follows:
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8000~8001 |
Laser height axis slot number |
0 |
6 |
0 |
|
|
8002~8003 |
Focus axis slot number |
0 |
6 |
0 |
|
|
8004~8005 |
Tip touch minimum value |
-2147483648 |
2147483647 |
0 |
|
|
8006~8007 |
Tip far maximum value |
-2147483648 |
2147483647 |
0 |
|
|
8008~8009 |
Number of samples during calibration |
2 |
19 |
0 |
count |
|
8010~8011 |
Laser height axis safety position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8012~8013 |
Number of retry attempts for type touch alarm |
0 |
2147483647 |
0 |
count |
|
8014~8015 |
Gas injection time before automatic operation |
0 |
999999 |
0 |
ms |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8020~8021 |
Z calibration 1st measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8022~8023 |
Z calibration 2nd measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8024~8025 |
Z calibration 3rd measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8026~8027 |
Z calibration 4th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8028~8029 |
Z calibration 5th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8030~8031 |
Z calibration 5th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8032~8033 |
Z calibration 7th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8034~8035 |
Z calibration 8th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8036~8037 |
Z calibration 9th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8038~8039 |
Z calibration 10th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8040~8041 |
Z calibration 11th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8042~8043 |
Z calibration 12th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8044~8045 |
Z calibration 13th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8046~8047 |
Z calibration 14th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8048~8049 |
Z calibration 15th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8050~8051 |
Z calibration 16th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8052~8053 |
Z calibration 17th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8054~8055 |
Z calibration 18th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
8056~8057 |
Z calibration 19th measurement position |
-2147483648 |
2147483647 |
0.0000 |
mm/inch |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8060~8061 |
Z calibration 1st measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8062~8063 |
Z calibration 2nd measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8064~8065 |
Z calibration 3st measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8066~8067 |
Z calibration 4th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8068~8069 |
Z calibration 5th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8070~8071 |
Z calibration 6th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8072~8073 |
Z calibration 7th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8074~8075 |
Z calibration 8th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8076~8077 |
Z calibration 9th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8078~8079 |
Z calibration 10th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8080~8081 |
Z calibration 11th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8082~8083 |
Z calibration 12th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8084~8085 |
Z calibration 13th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8086~8087 |
Z calibration 14th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8088~8089 |
Z calibration 15th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8090~8091 |
Z calibration 16th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8092~8093 |
Z calibration 17th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8094~8095 |
Z calibration 18th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
8096~8097 |
Z calibration 19th measured analog value |
-2147483648 |
2147483647 |
0 |
|
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8100~8101 |
Height control PID P gain |
0 |
10000 |
0.00 |
|
|
8102~8103 |
Height control PID I gain |
0 |
10000 |
0.00 |
|
|
8104~8105 |
Height control PID D gain |
0 |
10000 |
0.00 |
|
|
8106~8107 |
Height control PID min. output value |
-10000 |
10000 |
0.00 |
|
|
8108~8109 |
Height control PID max. output value |
-10000 |
10000 |
0.00 |
|
|
8110~8111 |
Height control PID max. output speed |
0 |
100000 |
0 |
|
|
8112~8113 |
Number of piercing steps to be processed |
1 |
10 |
0 |
step |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8120~8121 |
Piercing 1st step piercing time |
0 |
100000 |
0 |
ms |
|
8122~8123 |
Piercing 1st step gas type |
0 |
2 |
0 |
|
|
8124~8125 |
Piercing 1st step focus initial position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8126~8127 |
Piercing 1st step focus target position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8128~8129 |
Piercing 1st step initial Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8130~8131 |
Piercing 1st step target Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8132~8133 |
Piercing 1st step pressure initial value |
0 |
10000 |
0.00 |
bar |
|
8134~8135 |
Piercing 1st step pressure target value |
0 |
10000 |
0.00 |
bar |
|
8136~8137 |
Piercing 1st step power initial value |
0 |
100000 |
0 |
W |
|
8138~8139 |
Piercing 1st step power target value |
0 |
100000 |
0 |
W |
|
8140~8141 |
Piercing 1st step duty initial value |
0 |
100 |
0 |
% |
|
8142~8143 |
Piercing 1st step duty target value |
0 |
100 |
0 |
% |
|
8144~8145 |
Piercing 1st step frequency initial value |
0 |
5000 |
0 |
hz |
|
8146~8147 |
Piercing 1st step frequency target value |
0 |
5000 |
0 |
hz |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8160~8161 |
Piercing 2nd step piercing time |
0 |
100000 |
0 |
ms |
|
8162~8163 |
Piercing 2nd step gas type |
0 |
2 |
0 |
|
|
8164~8165 |
Piercing 2nd step focus initial position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8166~8167 |
Piercing 2nd step focus target position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8168~8169 |
Piercing 2nd step initial Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8170~8171 |
Piercing 2nd step target Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8172~8173 |
Piercing 2nd step pressure initial value |
0 |
10000 |
0.00 |
bar |
|
8174~8175 |
Piercing 2nd step pressure target value |
0 |
10000 |
0.00 |
bar |
|
8176~8177 |
Piercing 2nd step power initial value |
0 |
100000 |
0 |
W |
|
8178~8179 |
Piercing 2nd step power target value |
0 |
100000 |
0 |
W |
|
8180~8181 |
Piercing 2nd step duty initial value |
0 |
100 |
0 |
% |
|
8182~8183 |
Piercing 2nd step duty target value |
0 |
100 |
0 |
% |
|
8184~8185 |
Piercing 2nd step frequency initial value |
0 |
5000 |
0 |
hz |
|
8186~8187 |
Piercing 2nd step frequency target value |
0 |
5000 |
0 |
hz |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8200~8201 |
Piercing 3rd step piercing time |
0 |
100000 |
0 |
ms |
|
8202~8203 |
Piercing 3rd step gas type |
0 |
2 |
0 |
|
|
8204~8205 |
Piercing 3rd step focus initial position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8206~8207 |
Piercing 3rd step focus target position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8208~8209 |
Piercing 3rd step initial Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8210~8211 |
Piercing 3rd step target Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8212~8213 |
Piercing 3rd step pressure initial value |
0 |
10000 |
0.00 |
bar |
|
8214~8215 |
Piercing 3rd step pressure target value |
0 |
10000 |
0.00 |
bar |
|
8216~8217 |
Piercing 3rd step power initial value |
0 |
100000 |
0 |
W |
|
8218~8219 |
Piercing 3rd step power target value |
0 |
100000 |
0 |
W |
|
8220~8221 |
Piercing 3rd step duty initial value |
0 |
100 |
0 |
% |
|
8222~8223 |
Piercing 3rd step duty target value |
0 |
100 |
0 |
% |
|
8224~8225 |
Piercing 3rd step frequency initial value |
0 |
5000 |
0 |
hz |
|
8226~8227 |
Piercing 3rd step frequency target value |
0 |
5000 |
0 |
hz |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8240~8241 |
Piercing 4th step piercing time |
0 |
100000 |
0 |
ms |
|
8242~8243 |
Piercing 4th step gas type |
0 |
2 |
0 |
|
|
8244~8245 |
Piercing 4th step focus initial position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8246~8247 |
Piercing 4th step focus target position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8248~8249 |
Piercing 4th step initial Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8250~8251 |
Piercing 4th step target Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8252~8253 |
Piercing 4th step pressure initial value |
0 |
10000 |
0.00 |
bar |
|
8254~8255 |
Piercing 4th step pressure target value |
0 |
10000 |
0.00 |
bar |
|
8256~8257 |
Piercing 4th step power initial value |
0 |
100000 |
0 |
W |
|
8258~8259 |
Piercing 4th step power target value |
0 |
100000 |
0 |
W |
|
8260~8261 |
Piercing 4th step duty initial value |
0 |
100 |
0 |
% |
|
8262~8263 |
Piercing 4th step duty target value |
0 |
100 |
0 |
% |
|
8264~8265 |
Piercing 4th step frequency initial value |
0 |
5000 |
0 |
hz |
|
8266~8267 |
Piercing 4th step frequency target value |
0 |
5000 |
0 |
hz |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8280~8281 |
Piercing 5th step piercing time |
0 |
100000 |
0 |
ms |
|
8282~8283 |
Piercing 5th step gas type |
0 |
2 |
0 |
|
|
8284~8285 |
Piercing 5th step focus initial position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8286~8287 |
Piercing 5th step focus target position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8288~8289 |
Piercing 5th step initial Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8290~8291 |
Piercing 5th step target Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8292~8293 |
Piercing 5th step pressure initial value |
0 |
10000 |
0.00 |
bar |
|
8294~8295 |
Piercing 5th step pressure target value |
0 |
10000 |
0.00 |
bar |
|
8296~8297 |
Piercing 5th step power initial value |
0 |
100000 |
0 |
W |
|
8298~8299 |
Piercing 5th step power target value |
0 |
100000 |
0 |
W |
|
8300~8301 |
Piercing 5th step duty initial value |
0 |
100 |
0 |
% |
|
8302~8303 |
Piercing 5th step duty target value |
0 |
100 |
0 |
% |
|
8304~8305 |
Piercing 5th step frequency initial value |
0 |
5000 |
0 |
hz |
|
8306~8307 |
Piercing 5th step frequency target value |
0 |
5000 |
0 |
hz |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8320~8321 |
Piercing 6th step piercing time |
0 |
100000 |
0 |
ms |
|
8322~8323 |
Piercing 6th step gas type |
0 |
2 |
0 |
|
|
8324~8325 |
Piercing 6th step focus initial position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8326~8327 |
Piercing 6th step focus target position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8328~8329 |
Piercing 6th step initial Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8330~8331 |
Piercing 6th step target Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8332~8333 |
Piercing 6th step pressure initial value |
0 |
10000 |
0.00 |
bar |
|
8334~8335 |
Piercing 6th step pressure target value |
0 |
10000 |
0.00 |
bar |
|
8336~8337 |
Piercing 6th step power initial value |
0 |
100000 |
0 |
W |
|
8338~8339 |
Piercing 6th step power target value |
0 |
100000 |
0 |
W |
|
8340~8341 |
Piercing 6th step duty initial value |
0 |
100 |
0 |
% |
|
8342~8343 |
Piercing 6th step duty target value |
0 |
100 |
0 |
% |
|
8344~8345 |
Piercing 6th step frequency initial value |
0 |
5000 |
0 |
hz |
|
8346~8347 |
Piercing 6th step frequency target value |
0 |
5000 |
0 |
hz |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8360~8361 |
Piercing 7th step piercing time |
0 |
100000 |
0 |
ms |
|
8362~8363 |
Piercing 7th step gas type |
0 |
2 |
0 |
|
|
8364~8365 |
Piercing 7th step focus initial position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8366~8367 |
Piercing 7th step focus target position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8368~8369 |
Piercing 7th step initial Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8370~8371 |
Piercing 7th step target Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8372~8373 |
Piercing 7th step pressure initial value |
0 |
10000 |
0.00 |
bar |
|
8374~8375 |
Piercing 7th step pressure target value |
0 |
10000 |
0.00 |
bar |
|
8376~8377 |
Piercing 7th step power initial value |
0 |
100000 |
0 |
W |
|
8378~8379 |
Piercing 7th step power target value |
0 |
100000 |
0 |
W |
|
8380~8381 |
Piercing 7th step duty initial value |
0 |
100 |
0 |
% |
|
8382~8383 |
Piercing 7th step duty target value |
0 |
100 |
0 |
% |
|
8384~8385 |
Piercing 7th step frequency initial value |
0 |
5000 |
0 |
hz |
|
8386~8387 |
Piercing 7th step frequency target value |
0 |
5000 |
0 |
hz |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8400~8401 |
Piercing 8th step piercing time |
0 |
100000 |
0 |
ms |
|
8402~8403 |
Piercing 8th step gas type |
0 |
2 |
0 |
|
|
8404~8405 |
Piercing 8th step focus initial position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8406~8407 |
Piercing 8th step focus target position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8408~8409 |
Piercing 8th step initial Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8410~8411 |
Piercing 8th step target Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8412~8413 |
Piercing 8th step pressure initial value |
0 |
10000 |
0.00 |
bar |
|
8414~8415 |
Piercing 8th step pressure target value |
0 |
10000 |
0.00 |
bar |
|
8416~8417 |
Piercing 8th step power initial value |
0 |
100000 |
0 |
W |
|
8418~8419 |
Piercing 8th step power target value |
0 |
100000 |
0 |
W |
|
8420~8421 |
Piercing 8th step duty initial value |
0 |
100 |
0 |
% |
|
8422~8423 |
Piercing 8th step duty target value |
0 |
100 |
0 |
% |
|
8424~8425 |
Piercing 8th step frequency initial value |
0 |
5000 |
0 |
hz |
|
8426~8427 |
Piercing 8th step frequency target value |
0 |
5000 |
0 |
hz |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8440~8441 |
Piercing 9th step piercing time |
0 |
100000 |
0 |
ms |
|
8442~8443 |
Piercing 9th step gas type |
0 |
2 |
0 |
|
|
8444~8445 |
Piercing 9th step focus initial position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8446~8447 |
Piercing 9th step focus target position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8448~8449 |
Piercing 9th step initial Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8450~8451 |
Piercing 9th step target Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8452~8453 |
Piercing 9th step pressure initial value |
0 |
10000 |
0.00 |
bar |
|
8454~8455 |
Piercing 9th step pressure target value |
0 |
10000 |
0.00 |
bar |
|
8456~8457 |
Piercing 9th step power initial value |
0 |
100000 |
0 |
W |
|
8458~8459 |
Piercing 9th step power target value |
0 |
100000 |
0 |
W |
|
8460~8461 |
Piercing 9th step duty initial value |
0 |
100 |
0 |
% |
|
8462~8463 |
Piercing 9th step duty target value |
0 |
100 |
0 |
% |
|
8464~8465 |
Piercing 9th step frequency initial value |
0 |
5000 |
0 |
hz |
|
8466~8467 |
Piercing 9th step frequency target value |
0 |
5000 |
0 |
hz |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8480~8481 |
Piercing 10th step piercing time |
0 |
100000 |
0 |
ms |
|
8482~8483 |
Piercing 10th step gas type |
0 |
2 |
0 |
|
|
8484~8485 |
Piercing 10th step focus initial position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8486~8487 |
Piercing 10th step focus target position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8488~8489 |
Piercing 10th step initial Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8490~8491 |
Piercing 10th step target Z position |
0 |
300000 |
0.0000 |
mm/inch |
|
8492~8493 |
Piercing 10th step pressure initial value |
0 |
10000 |
0.00 |
bar |
|
8494~8495 |
Piercing 10th step pressure target value |
0 |
10000 |
0.00 |
bar |
|
8496~8497 |
Piercing 10th step power initial value |
0 |
100000 |
0 |
W |
|
8498~8499 |
Piercing 10th step power target value |
0 |
100000 |
0 |
W |
|
8500~8501 |
Piercing 10th step duty initial value |
0 |
100 |
0 |
% |
|
8502~8503 |
Piercing 10th step duty target value |
0 |
100 |
0 |
% |
|
8504~8505 |
Piercing 10th step frequency initial value |
0 |
5000 |
0 |
hz |
|
8506~8507 |
Piercing 10th step frequency target value |
0 |
5000 |
0 |
hz |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8600~8601 |
Analog to bar conversion multiplier value |
1 |
1000000 |
0 |
|
|
8602~8603 |
Analog to bar conversion divisor value |
1 |
1000000 |
0 |
|
|
8604~8605 |
Bar to analog conversion multiplier value |
1 |
1000000 |
0 |
|
|
8606~8607 |
Bar to analog conversion divisor value |
1 |
1000000 |
0 |
|
|
8608~8609 |
Analog to power conversion multiplier value |
1 |
1000000 |
0 |
|
|
8610~8611 |
Analog to power conversion divisor value |
1 |
1000000 |
0 |
|
|
8612~8613 |
Power to analog conversion multiplier value |
1 |
1000000 |
0 |
|
|
8614~8615 |
Power to analog conversion divisor value |
1 |
1000000 |
0 |
|
|
8616~8617 |
Duty to analog conversion multiplier value |
1 |
1000000 |
0 |
|
|
8618~8619 |
Duty to analog conversion divisor value |
1 |
1000000 |
0 |
|
|
8620~8621 |
Pressure analog input offset value |
0 |
32767 |
0 |
|
|
8622~8623 |
Low gas pressure warning level |
0 |
10000 |
0.00 |
bar |
|
8624~8625 |
Low gas pressure warning delay |
0 |
100000 |
0 |
ms |
|
8626~8627 |
Low pressure alarm level |
0 |
10000 |
0.00 |
bar |
|
8628~8629 |
Low pressure alarm delay |
0 |
100000 |
0 |
ms |
The list of technology blocks used in the laser cutting machine is as follows:
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8720~8721 |
Selected technology block |
0 |
9 |
0 |
|
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8800~8801 |
Tech. block 1: Cutting power |
0 |
100000 |
0 |
W |
|
8802~8803 |
Tech. block 1: Cutting height |
0 |
250000 |
0.0000 |
mm/inch |
|
8804~8805 |
Tech. block 1: Cutting feed |
0 |
100000 |
0 |
|
|
8806~8807 |
Tech. block 1: Gas type |
0 |
2 |
0 |
|
|
8808~8809 |
Tech. block 1: Gas pressure |
0 |
10000 |
0.00 |
bar |
|
8810~8811 |
Tech. block 1: Lead-In power |
0 |
100000 |
0 |
W |
|
8812~8813 |
Tech. block 1: Lead-In feed |
0 |
100000 |
0 |
|
|
8814~8815 |
Tech. block 1: Lead-In duty |
0 |
100 |
0 |
% |
|
8816~8817 |
Tech. block 1: Lens |
0 |
2 |
0 |
|
|
8818~8819 |
Tech. block 1: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
8820~8821 |
Tech. block 1: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
8822~8823 |
Tech. block 1: Focus position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8824~8825 |
Tech. block 1: Inner kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
8826~8827 |
Tech. block 1: Outer kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
8828~8829 |
Tech. block 1: Axis acceleration value |
0 |
10000 |
0.00 |
% |
|
8830~8831 |
Tech. block 1: Frequency |
0 |
100000 |
0 |
hz |
|
8832~8833 |
Tech. block 1: Duty |
0 |
100 |
0 |
% |
|
8834~8835 |
Tech. block 1: Lead-In delay |
0 |
100000 |
0 |
ms |
|
8836~8837 |
Tech. block 1: Tip-Touch alarm delay |
0 |
100000 |
0 |
ms |
|
8838~8839 |
Tech. block 1: Z axis operation mode |
0 |
1 |
0 |
|
|
8840~8841 |
Tech. block 1: Corner power |
0 |
100000 |
0 |
W |
|
8842~8843 |
Tech. block 1: Corner frequency |
0 |
100000 |
0 |
hz |
|
8844~8845 |
Tech. block 1: Corner duty |
0 |
100 |
0 |
% |
|
8846~8847 |
Tech. block 1: Corner cutting feed |
0 |
100000 |
0 |
|
|
8848~8849 |
Tech. block 1: Corner gas pressure |
0 |
10000 |
0.00 |
bar |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8860~8861 |
Tech. block 2: Cutting power |
0 |
100000 |
0 |
W |
|
8862~8863 |
Tech. block 2: Cutting height |
0 |
250000 |
0.0000 |
mm/inch |
|
8864~8865 |
Tech. block 2: Cutting feed |
0 |
100000 |
0 |
|
|
8866~8867 |
Tech. block 2: Gas type |
0 |
2 |
0 |
|
|
8868~8869 |
Tech. block 2: Gas pressure |
0 |
10000 |
0.00 |
bar |
|
8870~8871 |
Tech. block 2: Lead-In power |
0 |
100000 |
0 |
W |
|
8872~8873 |
Tech. block 2: Lead-In feed |
0 |
100000 |
0 |
|
|
8874~8875 |
Tech. block 2: Lead-In duty |
0 |
100 |
0 |
% |
|
8876~8877 |
Tech. block 2: Lens |
0 |
2 |
0 |
|
|
8878~8879 |
Tech. block 2: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
8880~8881 |
Tech. block 2: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
8882~8883 |
Tech. block 2: Focus position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8884~8885 |
Tech. block 2: Inner kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
8886~8887 |
Tech. block 2: Outer kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
8888~8889 |
Tech. block 2: Axis acceleration value |
0 |
10000 |
0.00 |
% |
|
8890~8891 |
Tech. block 2: Frequency |
0 |
100000 |
0 |
hz |
|
8892~8893 |
Tech. block 2: Duty |
0 |
100 |
0 |
% |
|
8894~8895 |
Tech. block 2: Lead-In delay |
0 |
100000 |
0 |
ms |
|
8896~8897 |
Tech. block 2: Tip-Touch alarm delay |
0 |
100000 |
0 |
ms |
|
8898~8899 |
Tech. block 2: Z axis operation mode |
0 |
1 |
0 |
|
|
8900~8901 |
Tech. block 2: Corner power |
0 |
100000 |
0 |
W |
|
8902~8903 |
Tech. block 2: Corner frequency |
0 |
100000 |
0 |
hz |
|
8904~8905 |
Tech. block 2: Corner duty |
0 |
100 |
0 |
% |
|
8906~8907 |
Tech. block 2: Corner cutting feed |
0 |
100000 |
0 |
|
|
8908~8909 |
Tech. block 2: Corner gas pressure |
0 |
10000 |
0.00 |
bar |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8920~8921 |
Tech. block 3: Cutting power |
0 |
100000 |
0 |
W |
|
8922~8923 |
Tech. block 3: Cutting height |
0 |
250000 |
0.0000 |
mm/inch |
|
8924~8925 |
Tech. block 3: Cutting feed |
0 |
100000 |
0 |
|
|
8926~8927 |
Tech. block 3: Gas type |
0 |
2 |
0 |
|
|
8928~8929 |
Tech. block 3: Gas pressure |
0 |
10000 |
0.00 |
bar |
|
8930~8931 |
Tech. block 3: Lead-In power |
0 |
100000 |
0 |
W |
|
8932~8933 |
Tech. block 3: Lead-In feed |
0 |
100000 |
0 |
|
|
8934~8935 |
Tech. block 3: Lead-In duty |
0 |
100 |
0 |
% |
|
8936~8937 |
Tech. block 3: Lens |
0 |
2 |
0 |
|
|
8938~8939 |
Tech. block 3: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
8940~8941 |
Tech. block 3: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
8942~8943 |
Tech. block 3: Focus position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
8944~8945 |
Tech. block 3: Inner kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
8946~8947 |
Tech. block 3: Outer kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
8948~8949 |
Tech. block 3: Axis acceleration value |
0 |
10000 |
0.00 |
% |
|
8950~8951 |
Tech. block 3: Frequency |
0 |
100000 |
0 |
hz |
|
8952~8953 |
Tech. block 3: Duty |
0 |
100 |
0 |
% |
|
8954~8955 |
Tech. block 3: Lead-In delay |
0 |
100000 |
0 |
ms |
|
8956~8957 |
Tech. block 3: Tip-Touch alarm delay |
0 |
100000 |
0 |
ms |
|
8958~8959 |
Tech. block 3: Z axis operation mode |
0 |
1 |
0 |
|
|
8960~8961 |
Tech. block 3: Corner power |
0 |
100000 |
0 |
W |
|
8962~8963 |
Tech. block 3: Corner frequency |
0 |
100000 |
0 |
hz |
|
8964~8965 |
Tech. block 3: Corner duty |
0 |
100 |
0 |
% |
|
8966~8967 |
Tech. block 3: Corner cutting feed |
0 |
100000 |
0 |
|
|
8968~8969 |
Tech. block 3: Corner gas pressure |
0 |
10000 |
0.00 |
bar |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8980~8981 |
Tech. block 4: Cutting power |
0 |
100000 |
0 |
W |
|
8982~8983 |
Tech. block 4: Cutting height |
0 |
250000 |
0.0000 |
mm/inch |
|
8984~8985 |
Tech. block 4: Cutting feed |
0 |
100000 |
0 |
|
|
8986~8987 |
Tech. block 4: Gas type |
0 |
2 |
0 |
|
|
8988~8989 |
Tech. block 4: Gas pressure |
0 |
10000 |
0.00 |
bar |
|
8990~8991 |
Tech. block 4: Lead-In power |
0 |
100000 |
0 |
W |
|
8992~8993 |
Tech. block 4: Lead-In feed |
0 |
100000 |
0 |
|
|
8994~8995 |
Tech. block 4: Lead-In duty |
0 |
100 |
0 |
% |
|
8996~8997 |
Tech. block 4: Lens |
0 |
2 |
0 |
|
|
8998~8999 |
Tech. block 4: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
9000~9001 |
Tech. block 4: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
9002~9003 |
Tech. block 4: Focus position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
9004~9005 |
Tech. block 4: Inner kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
9006~9007 |
Tech. block 4: Outer kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
9008~9009 |
Tech. block 4: Axis acceleration value |
0 |
10000 |
0.00 |
% |
|
9010~9011 |
Tech. block 4: Frequency |
0 |
100000 |
0 |
hz |
|
9012~9013 |
Tech. block 4: Duty |
0 |
100 |
0 |
% |
|
9014~9015 |
Tech. block 4: Lead-In delay |
0 |
100000 |
0 |
ms |
|
9016~9017 |
Tech. block 4: Tip-Touch alarm delay |
0 |
100000 |
0 |
ms |
|
9018~9019 |
Tech. block 4: Z axis operation mode |
0 |
1 |
0 |
|
|
9020~9021 |
Tech. block 4: Corner power |
0 |
100000 |
0 |
W |
|
9022~9023 |
Tech. block 4: Corner frequency |
0 |
100000 |
0 |
hz |
|
9024~9025 |
Tech. block 4: Corner duty |
0 |
100 |
0 |
% |
|
9026~9027 |
Tech. block 4: Corner cutting feed |
0 |
100000 |
0 |
|
|
9028~9029 |
Tech. block 4: Corner gas pressure |
0 |
10000 |
0.00 |
bar |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
9040~9041 |
Tech. block 5: Cutting power |
0 |
100000 |
0 |
W |
|
9042~9043 |
Tech. block 5: Cutting height |
0 |
250000 |
0.0000 |
mm/inch |
|
9044~9045 |
Tech. block 5: Cutting feed |
0 |
100000 |
0 |
|
|
9046~9047 |
Tech. block 5: Gas type |
0 |
2 |
0 |
|
|
9048~9049 |
Tech. block 5: Gas pressure |
0 |
10000 |
0.00 |
bar |
|
9050~9051 |
Tech. block 5: Lead-In power |
0 |
100000 |
0 |
W |
|
9052~9053 |
Tech. block 5: Lead-In feed |
0 |
100000 |
0 |
|
|
9054~9055 |
Tech. block 5: Lead-In duty |
0 |
100 |
0 |
% |
|
9056~9057 |
Tech. block 5: Lens |
0 |
2 |
0 |
|
|
9058~9059 |
Tech. block 5: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
9060~9061 |
Tech. block 5: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
9062~9063 |
Tech. block 5: Focus position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
9064~9065 |
Tech. block 5: Inner kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
9066~9067 |
Tech. block 5: Outer kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
9068~9069 |
Tech. block 5: Axis acceleration value |
0 |
10000 |
0.00 |
% |
|
9070~9071 |
Tech. block 5: Frequency |
0 |
100000 |
0 |
hz |
|
9072~9073 |
Tech. block 5: Duty |
0 |
100 |
0 |
% |
|
9074~9075 |
Tech. block 5: Lead-In delay |
0 |
100000 |
0 |
ms |
|
9076~9077 |
Tech. block 5: Tip-Touch alarm delay |
0 |
100000 |
0 |
ms |
|
9078~9079 |
Tech. block 5: Z axis operation mode |
0 |
1 |
0 |
|
|
9080~9081 |
Tech. block 5: Corner power |
0 |
100000 |
0 |
W |
|
9082~9083 |
Tech. block 5: Corner frequency |
0 |
100000 |
0 |
hz |
|
9084~9085 |
Tech. block 5: Corner duty |
0 |
100 |
0 |
% |
|
9086~9087 |
Tech. block 5: Corner cutting feed |
0 |
100000 |
0 |
|
|
9088~9089 |
Tech. block 5: Corner gas pressure |
0 |
10000 |
0.00 |
bar |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
9100~9101 |
Tech. block 6: Cutting power |
0 |
100000 |
0 |
W |
|
9102~9103 |
Tech. block 6: Cutting height |
0 |
250000 |
0.0000 |
mm/inch |
|
9104~9105 |
Tech. block 6: Cutting feed |
0 |
100000 |
0 |
|
|
9106~9107 |
Tech. block 6: Gas type |
0 |
2 |
0 |
|
|
9108~9109 |
Tech. block 6: Gas pressure |
0 |
10000 |
0.00 |
bar |
|
9110~9111 |
Tech. block 6: Lead-In power |
0 |
100000 |
0 |
W |
|
9112~9113 |
Tech. block 6: Lead-In feed |
0 |
100000 |
0 |
|
|
9114~9115 |
Tech. block 6: Lead-In duty |
0 |
100 |
0 |
% |
|
9116~9117 |
Tech. block 6: Lens |
0 |
2 |
0 |
|
|
9118~9119 |
Tech. block 6: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
9120~9121 |
Tech. block 6: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
9122~9123 |
Tech. block 6: Focus position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
9124~9125 |
Tech. block 6: Inner kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
9126~9127 |
Tech. block 6: Outer kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
9128~9129 |
Tech. block 6: Axis acceleration value |
0 |
10000 |
0.00 |
% |
|
9130~9131 |
Tech. block 6: Frequency |
0 |
100000 |
0 |
hz |
|
9132~9133 |
Tech. block 6: Duty |
0 |
100 |
0 |
% |
|
9134~9135 |
Tech. block 6: Lead-In delay |
0 |
100000 |
0 |
ms |
|
9136~9137 |
Tech. block 6: Tip-Touch alarm delay |
0 |
100000 |
0 |
ms |
|
9138~9139 |
Tech. block 6: Z axis operation mode |
0 |
1 |
0 |
|
|
9140~9141 |
Tech. block 6: Corner power |
0 |
100000 |
0 |
W |
|
9142~9143 |
Tech. block 6: Corner frequency |
0 |
100000 |
0 |
hz |
|
9144~9145 |
Tech. block 6: Corner duty |
0 |
100 |
0 |
% |
|
9146~9147 |
Tech. block 6: Corner cutting feed |
0 |
100000 |
0 |
|
|
9148~9149 |
Tech. block 6: Corner gas pressure |
0 |
10000 |
0.00 |
bar |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
9160~9161 |
Tech. block 7: Cutting power |
0 |
100000 |
0 |
W |
|
9162~9163 |
Tech. block 7: Cutting height |
0 |
250000 |
0.0000 |
mm/inch |
|
9164~9165 |
Tech. block 7: Cutting feed |
0 |
100000 |
0 |
|
|
9166~9167 |
Tech. block 7: Gas type |
0 |
2 |
0 |
|
|
9168~9169 |
Tech. block 7: Gas pressure |
0 |
10000 |
0.00 |
bar |
|
9170~9171 |
Tech. block 7: Lead-In power |
0 |
100000 |
0 |
W |
|
9172~9173 |
Tech. block 7: Lead-In feed |
0 |
100000 |
0 |
|
|
9174~9175 |
Tech. block 7: Lead-In duty |
0 |
100 |
0 |
% |
|
9176~9177 |
Tech. block 7: Lens |
0 |
2 |
0 |
|
|
9178~9179 |
Tech. block 7: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
9180~9181 |
Tech. block 7: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
9182~9183 |
Tech. block 7: Focus position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
9184~9185 |
Tech. block 7: Inner kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
9186~9187 |
Tech. block 7: Outer kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
9188~9189 |
Tech. block 7: Axis acceleration value |
0 |
10000 |
0.00 |
% |
|
9190~9191 |
Tech. block 7: Frequency |
0 |
100000 |
0 |
hz |
|
9192~9193 |
Tech. block 7: Duty |
0 |
100 |
0 |
% |
|
9194~9195 |
Tech. block 7: Lead-In delay |
0 |
100000 |
0 |
ms |
|
9196~9197 |
Tech. block 7: Tip-Touch alarm delay |
0 |
100000 |
0 |
ms |
|
9198~9199 |
Tech. block 7: Z axis operation mode |
0 |
1 |
0 |
|
|
9200~9201 |
Tech. block 7: Corner power |
0 |
100000 |
0 |
W |
|
9202~9203 |
Tech. block 7: Corner frequency |
0 |
100000 |
0 |
hz |
|
9204~9205 |
Tech. block 7: Corner duty |
0 |
100 |
0 |
% |
|
9206~9207 |
Tech. block 7: Corner cutting feed |
0 |
100000 |
0 |
|
|
9208~9209 |
Tech. block 7: Corner gas pressure |
0 |
10000 |
0.00 |
bar |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
9220~9221 |
Tech. block 8: Cutting power |
0 |
100000 |
0 |
W |
|
9222~9223 |
Tech. block 8: Cutting height |
0 |
250000 |
0.0000 |
mm/inch |
|
9224~9225 |
Tech. block 8: Cutting feed |
0 |
100000 |
0 |
|
|
9226~9227 |
Tech. block 8: Gas type |
0 |
2 |
0 |
|
|
9228~9229 |
Tech. block 8: Gas pressure |
0 |
10000 |
0.00 |
bar |
|
9230~9231 |
Tech. block 8: Lead-In power |
0 |
100000 |
0 |
W |
|
9232~9233 |
Tech. block 8: Lead-In feed |
0 |
100000 |
0 |
|
|
9234~9235 |
Tech. block 8: Lead-In duty |
0 |
100 |
0 |
% |
|
9236~9237 |
Tech. block 8: Lens |
0 |
2 |
0 |
|
|
9238~9239 |
Tech. block 8: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
9240~9241 |
Tech. block 8: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
9242~9243 |
Tech. block 8: Focus position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
9244~9245 |
Tech. block 8: Inner kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
9246~9247 |
Tech. block 8: Outer kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
9248~9249 |
Tech. block 8: Axis acceleration value |
0 |
10000 |
0.00 |
% |
|
9250~9251 |
Tech. block 8: Frequency |
0 |
100000 |
0 |
hz |
|
9252~9253 |
Tech. block 8: Duty |
0 |
100 |
0 |
% |
|
9254~9255 |
Tech. block 8: Lead-In delay |
0 |
100000 |
0 |
ms |
|
9256~9257 |
Tech. block 8: Tip-Touch alarm delay |
0 |
100000 |
0 |
ms |
|
9258~9259 |
Tech. block 8: Z axis operation mode |
0 |
1 |
0 |
|
|
9260~9261 |
Tech. block 8: Corner power |
0 |
100000 |
0 |
W |
|
9262~9263 |
Tech. block 8: Corner frequency |
0 |
100000 |
0 |
hz |
|
9264~9265 |
Tech. block 8: Corner duty |
0 |
100 |
0 |
% |
|
9266~9267 |
Tech. block 8: Corner cutting feed |
0 |
100000 |
0 |
|
|
9268~9269 |
Tech. block 8: Corner gas pressure |
0 |
10000 |
0.00 |
bar |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
9280~9281 |
Tech. block 9: Cutting power |
0 |
100000 |
0 |
W |
|
9282~9283 |
Tech. block 9: Cutting height |
0 |
250000 |
0.0000 |
mm/inch |
|
9284~9285 |
Tech. block 9: Cutting feed |
0 |
100000 |
0 |
|
|
9286~9287 |
Tech. block 9: Gas type |
0 |
2 |
0 |
|
|
9288~9289 |
Tech. block 9: Gas pressure |
0 |
10000 |
0.00 |
bar |
|
9290~9291 |
Tech. block 9: Lead-In power |
0 |
100000 |
0 |
W |
|
9292~9293 |
Tech. block 9: Lead-In feed |
0 |
100000 |
0 |
|
|
9294~9295 |
Tech. block 9: Lead-In duty |
0 |
100 |
0 |
% |
|
9296~9297 |
Tech. block 9: Lens |
0 |
2 |
0 |
|
|
9298~9299 |
Tech. block 9: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
9300~9301 |
Tech. block 9: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
9302~9303 |
Tech. block 9: Focus position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
9304~9305 |
Tech. block 9: Inner kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
9306~9307 |
Tech. block 9: Outer kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
9308~9309 |
Tech. block 9: Axis acceleration value |
0 |
10000 |
0.00 |
% |
|
9310~9311 |
Tech. block 9: Frequency |
0 |
100000 |
0 |
hz |
|
9312~9313 |
Tech. block 9: Duty |
0 |
100 |
0 |
% |
|
9314~9315 |
Tech. block 9: Lead-In delay |
0 |
100000 |
0 |
ms |
|
9316~9317 |
Tech. block 9: Tip-Touch alarm delay |
0 |
100000 |
0 |
ms |
|
9318~9319 |
Tech. block 9: Z axis operation mode |
0 |
1 |
0 |
|
|
9320~9321 |
Tech. block 9: Corner power |
0 |
100000 |
0 |
W |
|
9322~9323 |
Tech. block 9: Corner frequency |
0 |
100000 |
0 |
hz |
|
9324~9325 |
Tech. block 9: Corner duty |
0 |
100 |
0 |
% |
|
9326~9327 |
Tech. block 9: Corner cutting feed |
0 |
100000 |
0 |
|
|
9328~9329 |
Tech. block 9: Corner gas pressure |
0 |
10000 |
0.00 |
bar |
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
9340~9341 |
Tech. block 10: Cutting power |
0 |
100000 |
0 |
W |
|
9342~9343 |
Tech. block 10: Cutting height |
0 |
250000 |
0.0000 |
mm/inch |
|
9344~9345 |
Tech. block 10: Cutting feed |
0 |
100000 |
0 |
|
|
9346~9347 |
Tech. block 10: Gas type |
0 |
2 |
0 |
|
|
9348~9349 |
Tech. block 10: Gas pressure |
0 |
10000 |
0.00 |
bar |
|
9350~9351 |
Tech. block 10: Lead-In power |
0 |
100000 |
0 |
W |
|
9352~9353 |
Tech. block 10: Lead-In feed |
0 |
100000 |
0 |
|
|
9354~9355 |
Tech. block 10: Lead-In duty |
0 |
100 |
0 |
% |
|
9356~9357 |
Tech. block 10: Lens |
0 |
2 |
0 |
|
|
9358~9359 |
Tech. block 10: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
9360~9361 |
Tech. block 10: Nozzle type |
-2147483648 |
2147483647 |
0 |
string |
|
9362~9363 |
Tech. block 10: Focus position |
-250000 |
250000 |
0.0000 |
mm/inch |
|
9364~9365 |
Tech. block 10: Inner kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
9366~9367 |
Tech. block 10: Outer kerf |
0 |
10000 |
0.0000 |
mm/inch |
|
9368~9369 |
Tech. block 10: Axis acceleration value |
0 |
10000 |
0.00 |
% |
|
9370~9371 |
Tech. block 10: Frequency |
0 |
100000 |
0 |
hz |
|
9372~9373 |
Tech. block 10: Duty |
0 |
100 |
0 |
% |
|
9374~9375 |
Tech. block 10: Lead-In delay |
0 |
100000 |
0 |
ms |
|
9376~9377 |
Tech. block 10: Tip-Touch alarm delay |
0 |
100000 |
0 |
ms |
|
9378~9379 |
Tech. block 10: Z axis operation mode |
0 |
1 |
0 |
|
|
9380~9381 |
Tech. block 10: Corner power |
0 |
100000 |
0 |
W |
|
9382~9383 |
Tech. block 10: Corner frequency |
0 |
100000 |
0 |
hz |
|
9384~9385 |
Tech. block 10: Corner duty |
0 |
100 |
0 |
% |
|
9386~9387 |
Tech. block 10: Corner cutting feed |
0 |
100000 |
0 |
|
|
9388~9389 |
Tech. block 10: Corner gas pressure |
0 |
10000 |
0.00 |
bar |
Plasma Cutting Software
The list of parameters used in the plasma cutting machine is as follows:
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8000~8001 |
Height control (AHC) axis selection |
1 |
6 |
0 |
|
|
8002~8003 |
Height control PID P gain |
0 |
10000 |
0.00 |
|
|
8004~8005 |
Height control PID I gain |
0 |
10000 |
0.00 |
|
|
8006~8007 |
Height control PID D gain |
0 |
10000 |
0.00 |
|
|
8008~8009 |
Height control PID min. output value |
-10000 |
10000 |
0.00 |
|
|
8010~8011 |
Height control PID max. output value |
-10000 |
10000 |
0.00 |
|
|
8012~8013 |
Height control PID max. output speed |
0 |
100000 |
0 |
unit/min |
|
8014~8015 |
ip touch search speed |
0 |
100000 |
0 |
unit/min |
|
8016~8017 |
Waiting time to move after receiving plasma ready signal |
0 |
100000 |
0 |
ms |
|
8018~8019 |
Waiting time for PID to engage after cutting starts |
0 |
100000 |
0 |
ms |
|
8020~8021 |
Digital input number to which the tip touch signal is connected |
0 |
19 |
0 |
|
|
8022~8023 |
Digital input number to which the plasma ready signal is connected |
0 |
19 |
0 |
|
|
8024~8025 |
Address where the arc voltage signal will be read |
0 |
3999 |
0 |
|
|
8026~8027 |
Servo torque value to be used during tip touch probing |
0 |
3000 |
0.0 |
% |
|
8028~8029 |
Torque tolerance reached during tip touch probing |
0 |
1000 |
0.0 |
% |
|
8030~8031 |
Analog -> Arc voltage conversion multiplier |
1 |
100000 |
0 |
|
|
8032~8033 |
Analog -> Arc voltage conversion divisor |
1 |
100000 |
0 |
|
|
8034~8035 |
Machine coordinate to be reached with rapid speed before piercing |
-2000000000 |
2000000000 |
0.0000 |
mm/inch |
|
8036~8037 |
Waiting time before triggering an alarm after the plasma ready signal is lost during cutting |
0 |
100000 |
0 |
ms |
|
8038~8039 |
Cancel plasma ready signal lost alarm |
0 |
1 |
0 |
bool |
|
8040~8041 |
AHC shutdown distance at the end of the line |
0 |
2000000000 |
0.0000 |
mm/inch |
|
8042~8043 |
Offset number used for marking |
1 |
10 |
0 |
|
|
8044~8045 |
Arc voltage offset value |
0 |
10000 |
0.00 |
V |
|
8046~8047 |
Z coordinate for sheet surface cutting |
-2000000000 |
2000000000 |
0.0000 |
mm/inch |
|
8048~8049 |
Lift to Z safe coordinate with G71 |
0 |
1 |
0 |
bool |
|
8050~8051 |
Marking X offset value |
-2000000000 |
2000000000 |
0.0000 |
mm/inch |
|
8052~8053 |
Marking Y offset value |
-2000000000 |
2000000000 |
0.0000 |
mm/inch |
|
8054~8055 |
Laser pointer X offset value |
-2000000000 |
2000000000 |
0.0000 |
mm/inch |
|
8056~8057 |
Laser pointer Y offset value |
-2000000000 |
2000000000 |
0.0000 |
mm/inch |
Plasma cutting machine technology block data are as follows:
|
Address |
Description |
Minimum |
Maximum |
Format |
Unit |
|
8200~8201 |
Material type |
0 |
2000000000 |
0 |
|
|
8202~8203 |
Material thickness |
0 |
2000000000 |
0.0000 |
mm/inch |
|
8204~8205 |
Cutting power |
0 |
2000000000 |
0 |
A |
|
8206~8207 |
Cutting speed |
0 |
2000000000 |
0.0000 |
unit/min |
|
8208~8209 |
Piercing height |
0 |
2000000000 |
0.0000 |
mm/inch |
|
8210~8211 |
Cutting height |
0 |
2000000000 |
0.0000 |
mm/inch |
|
8212~8213 |
Piercing time |
0 |
2000000000 |
0 |
ms |
|
8214~8215 |
Arc voltage |
0 |
2000000000 |
0.00 |
V |
|
8216~8217 |
Reserved |
|
|
|
|
|
8218~8219 |
Kerf |
0 |
2000000000 |
0.0000 |
mm/inch |
|
8220~8221 |
Consumable material image |
0 |
2000000000 |
0 |
|
|
8222~8223 |
Plasma unit type |
0 |
2000000000 |
0 |
|
|
8224~8225 |
Marking speed |
0 |
2000000000 |
0.0000 |
unit/min |